Fresh install issue

Status
Not open for further replies.
Andyd358

Andyd358

Member
Aug 23, 2018
260
9
18
55
UK
Hi

Version 4.5.14
Git Information Branch: master

Debian 9.12

5 times today I have tried to install Fusion on a debian CT in proxmox each time I get the same problem I can add a gateway but it wont start and when i click on sip status I get "connection to event socket failed" also if i look at the log viewer it seem a little broke!!!

Any Ideas?

The only thing i can think of is that there may be an issue with proxmox. I know it does not like its IP address changed but it was setup on dhcp in a different location so I had to chaneg the ip and dns for it.


1591972869981.png
 
Last edited:
Adrian Fretwell

Adrian Fretwell

Well-Known Member
Aug 13, 2017
1,498
413
83
Last person I remember having that sort of trouble had accidentally installed the 32 bit version of Debian.
 
Andyd358

Andyd358

Member
Aug 23, 2018
260
9
18
55
UK
initially i was getting lots of locale errors directory not found when i was trying to install via ssh but ive since tried using the console on proxmox, dont get the errors any longer but still the same outcome.. I had the same issue with trying in on raspberry pi earlier in the week.
 
Andyd358

Andyd358

Member
Aug 23, 2018
260
9
18
55
UK
Only error i get when installing again (Debian 10 standard) this time is
Ver Cluster Port Status Owner Data directory Log file
11 main 5432 down postgres /var/lib/postgresql/11/main /var/log/postgresql/postgresql-11-main.log
update-alternatives: using /usr/share/postgresql/11/man/man1/postmaster.1.gz to provide /usr/share/man/man1/postmaster.1.gz (postmaster.1.gz) in auto mode
Setting up postgresql (11+200+deb10u3) ...
Setting up sysstat (12.0.3-2) ...
 
Andyd358

Andyd358

Member
Aug 23, 2018
260
9
18
55
UK
Seen another error at the end of the install
Job for freeswitch.service failed because the control process exited with error code.
See "systemctl status freeswitch.service" and "journalctl -xe" for details.

* freeswitch.service - freeswitch
Loaded: loaded (/lib/systemd/system/freeswitch.service; enabled; vendor preset: en
Active: failed (Result: exit-code) since Fri 2020-06-12 17:07:39 UTC; 22min ago
Process: 15918 ExecStartPre=/bin/mkdir -p /var/run/freeswitch (code=exited, status=

Jun 12 17:07:39 CT100 systemd[1]: freeswitch.service: Service RestartSec=100ms expire
Jun 12 17:07:39 CT100 systemd[1]: freeswitch.service: Scheduled restart job, restart
Jun 12 17:07:39 CT100 systemd[1]: Stopped freeswitch.
Jun 12 17:07:39 CT100 systemd[1]: freeswitch.service: Start request repeated too quic
Jun 12 17:07:39 CT100 systemd[1]: freeswitch.service: Failed with result 'exit-code'.
Jun 12 17:07:39 CT100 systemd[1]: Failed to start freeswitch.
lines 1-11/11 (END)
 
Adrian Fretwell

Adrian Fretwell

Well-Known Member
Aug 13, 2017
1,498
413
83
Difficult to call, but this may be a permissions issue. You really need some input from a Proxmox expert.
 
Andyd358

Andyd358

Member
Aug 23, 2018
260
9
18
55
UK
Could it be because im using proxmox do you think Ive never had an issue like this before, coul dit be related to this:

Is it possible to correctly launch fusionpвx/freeswitch in an unprivileged LXC on Proxmox VE?

Dear colleagues! Maybe I again raise the topic that was previously discussed here. But still... Tell me, please, is it possible to install Fusionpbx in an unprivileged container on Proxmox VE? If not, why? P.S. Yesterday I tried to install Fusionpbx in an unprivileged LXC on Proxmox VE 6.1 and...
www.pbxforums.com www.pbxforums.com
 
Adrian Fretwell

Adrian Fretwell

Well-Known Member
Aug 13, 2017
1,498
413
83
I don't know the answer. I know @DigitalDaz has some experience with Proxmox, maybe he (or others) will be able to provide a more educated guess than me.
 
Andyd358

Andyd358

Member
Aug 23, 2018
260
9
18
55
UK
Stangley I have had the same problem with a Raspberry Pi so i was thinking is there a proble with the master
 
Andyd358

Andyd358

Member
Aug 23, 2018
260
9
18
55
UK
Thought i would try again this morning but still getting the same error :
Success. You can now start the database server using:

pg_ctlcluster 12 main start

Ver Cluster Port Status Owner Data directory Log file
12 main 5432 down postgres /var/lib/postgresql/12/main /var/log/postgresql/postgresql-12-main.log
update-alternatives: using /usr/share/postgresql/12/man/man1/postmaster.1.gz to provide /usr/share/man/man1/postmaster.1.gz (postmaster.1.gz) in auto mode
Setting up postgresql (12+215.pgdg90+1) ...
Processing triggers for systemd (232-25+deb9u12) ...
CREATE DATABASE
CREATE DATABASE
CREATE ROLE
CREATE ROLE
GRANT
GRANT
GRANT
ALTER ROLE
ALTER ROLE
INSERT 0 1
INSERT 0 1
INSERT 0 1
Job for freeswitch.service failed because the control process exited with error code.
See "systemctl status freeswitch.service" and "journalctl -xe" for details.
 
Andyd358

Andyd358

Member
Aug 23, 2018
260
9
18
55
UK
* freeswitch.service - freeswitch
Loaded: loaded (/lib/systemd/system/freeswitch.service; enabled; vendor preset: enabled)
Active: failed (Result: exit-code) since Mon 2020-06-15 08:08:56 UTC; 35min ago
Process: 18034 ExecStartPre=/bin/mkdir -p /var/run/freeswitch (code=exited, status=214/SETSCHEDULER)

Jun 15 08:08:56 CT100 systemd[1]: freeswitch.service: Control process exited, code=exited status=214
Jun 15 08:08:56 CT100 systemd[1]: Failed to start freeswitch.
Jun 15 08:08:56 CT100 systemd[1]: freeswitch.service: Unit entered failed state.
Jun 15 08:08:56 CT100 systemd[1]: freeswitch.service: Failed with result 'exit-code'.
Jun 15 08:08:56 CT100 systemd[1]: freeswitch.service: Service hold-off time over, scheduling restart.
Jun 15 08:08:56 CT100 systemd[1]: Stopped freeswitch.
Jun 15 08:08:56 CT100 systemd[1]: freeswitch.service: Start request repeated too quickly.
Jun 15 08:08:56 CT100 systemd[1]: Failed to start freeswitch.
Jun 15 08:08:56 CT100 systemd[1]: freeswitch.service: Unit entered failed state.
Jun 15 08:08:56 CT100 systemd[1]: freeswitch.service: Failed with result 'exit-code'.

Jun 15 08:43:21 CT100 sshd[19242]: Received disconnect from 49.88.112.76 port 34039:11: [preauth]
Jun 15 08:43:21 CT100 sshd[19242]: Disconnected from 49.88.112.76 port 34039 [preauth]
Jun 15 08:43:21 CT100 sshd[19242]: PAM 2 more authentication failures; logname= uid=0 euid=0 tty=ssh ruser= rhost=49.88.112.76
Jun 15 08:43:53 CT100 sshd[19260]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=218.
Jun 15 08:43:55 CT100 sshd[19260]: Failed password for root from 218.92.0.173 port 22922 ssh2
Jun 15 08:43:58 CT100 sshd[19260]: Failed password for root from 218.92.0.173 port 22922 ssh2
Jun 15 08:44:01 CT100 sshd[19260]: Failed password for root from 218.92.0.173 port 22922 ssh2
Jun 15 08:44:04 CT100 sshd[19260]: Failed password for root from 218.92.0.173 port 22922 ssh2
Jun 15 08:44:07 CT100 sshd[19260]: Failed password for root from 218.92.0.173 port 22922 ssh2
Jun 15 08:44:07 CT100 sshd[19260]: error: maximum authentication attempts exceeded for root from 218.92.0.173 port 22922 ssh2 [
Jun 15 08:44:07 CT100 sshd[19260]: Disconnecting: Too many authentication failures [preauth]
Jun 15 08:44:07 CT100 sshd[19260]: PAM 4 more authentication failures; logname= uid=0 euid=0 tty=ssh ruser= rhost=218.92.0.173
Jun 15 08:44:07 CT100 sshd[19260]: PAM service(sshd) ignoring max retries; 5 > 3
Jun 15 08:44:16 CT100 sshd[19273]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=218.
Jun 15 08:44:18 CT100 sshd[19273]: Failed password for root from 218.92.0.173 port 61872 ssh2
Jun 15 08:44:21 CT100 sshd[19277]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=49.8
Jun 15 08:44:22 CT100 sshd[19273]: Failed password for root from 218.92.0.173 port 61872 ssh2
Jun 15 08:44:23 CT100 sshd[19277]: Failed password for root from 49.88.112.76 port 60386 ssh2
Jun 15 08:44:25 CT100 sshd[19277]: Failed password for root from 49.88.112.76 port 60386 ssh2
Jun 15 08:44:26 CT100 ntpd[1903]: local_clock: ntp_loopfilter.c line 818: ntp_adjtime: Operation not permitted
Jun 15 08:44:26 CT100 sshd[19273]: Failed password for root from 218.92.0.173 port 61872 ssh2
Jun 15 08:44:28 CT100 sshd[19277]: Failed password for root from 49.88.112.76 port 60386 ssh2
Jun 15 08:44:28 CT100 sshd[19277]: Received disconnect from 49.88.112.76 port 60386:11: [preauth]
Jun 15 08:44:28 CT100 sshd[19277]: Disconnected from 49.88.112.76 port 60386 [preauth]
Jun 15 08:44:28 CT100 sshd[19277]: PAM 2 more authentication failures; logname= uid=0 euid=0 tty=ssh ruser= rhost=49.88.112.76
Jun 15 08:44:29 CT100 sshd[19273]: Failed password for root from 218.92.0.173 port 61872 ssh2
Jun 15 08:44:34 CT100 sshd[19273]: Failed password for root from 218.92.0.173 port 61872 ssh2
Jun 15 08:44:37 CT100 sshd[19273]: Failed password for root from 218.92.0.173 port 61872 ssh2
Jun 15 08:44:37 CT100 sshd[19273]: error: maximum authentication attempts exceeded for root from 218.92.0.173 port 61872 ssh2 [
Jun 15 08:44:37 CT100 sshd[19273]: Disconnecting: Too many authentication failures [preauth]
Jun 15 08:44:37 CT100 sshd[19273]: PAM 5 more authentication failures; logname= uid=0 euid=0 tty=ssh ruser= rhost=218.92.0.173
Jun 15 08:44:37 CT100 sshd[19273]: PAM service(sshd) ignoring max retries; 6 > 3
Jun 15 08:44:44 CT100 sshd[19290]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=218.
Jun 15 08:44:46 CT100 sshd[19290]: Failed password for root from 218.92.0.173 port 31571 ssh2
Jun 15 08:44:47 CT100 sshd[19290]: Received disconnect from 218.92.0.173 port 31571:11: [preauth]
Jun 15 08:44:47 CT100 sshd[19290]: Disconnected from 218.92.0.173 port 31571 [preauth]
Jun 15 08:45:01 CT100 CRON[19301]: pam_unix(cron:session): session opened for user root by (uid=0)
Jun 15 08:45:01 CT100 CRON[19302]: (root) CMD (command -v debian-sa1 > /dev/null && debian-sa1 1 1)
Jun 15 08:45:01 CT100 CRON[19301]: pam_unix(cron:session): session closed for user root
lines 1114-1152/1152 (END)
 
Adrian Fretwell

Adrian Fretwell

Well-Known Member
Aug 13, 2017
1,498
413
83
As I said before, it does look like a permissions issue to me (but I know nothing about Proxmox). I assume it has failed to create the directory /var/run/freeswitch.

I believe the FreeSwitch startup process needs to start as root in order to execute things like /bin/mkdir -p /var/run/freeswitch and then drop its privileges to the www-data user specified by the -u on the command line.

Is there any more useful information written in the freeswitch log? (Assuming it has managed to get as far as creating a log file.)
 
Andyd358

Andyd358

Member
Aug 23, 2018
260
9
18
55
UK
Ok I think the Promox install is fubar somehow Ive just done a fresh install on a VPS using proxmox and its worked fine by the look of it. Just need to test with a sip trunk and a phone
 
Andyd358

Andyd358

Member
Aug 23, 2018
260
9
18
55
UK
Adrian Fretwell said:
As I said before, it does look like a permissions issue to me (but I know nothing about Proxmox). I assume it has failed to create the directory /var/run/freeswitch.

I believe the FreeSwitch startup process needs to start as root in order to execute things like /bin/mkdir -p /var/run/freeswitch and then drop its privileges to the www-data user specified by the -u on the command line.

Is there any more useful information written in the freeswitch log? (Assuming it has managed to get as far as creating a log file.)
Click to expand...
Ive checked persmissions for the freeswitch directory (nothing in the directory from what i can see)

drwxrwx--- 2 www-data www-data 40 Jun 15 09:54 freeswitch
 
Scott Williams

Scott Williams

Member
Feb 18, 2017
44
7
8
63
I was creating privileged containers, and Freeswitch would not install properly. Secondly it wouldn't sync time, so then I had to allow nesting.

HTH
 
  • Like
Reactions: Andyd358
Status
Not open for further replies.
Top Bottom